3D printing Kevlar fiber layer distributions and fiber orientations into nylon composites to achieve designable mechanical strength
09/04/2021 -
Additive Manufacturing, Volume 39Author(s): Kaiwen Shi, Yuekai Yan, Hui Mei, Chao Chen, Laifei Cheng
Digital light processing 3D printing Kevlar composites based on dual curing resin
09/04/2021 -
Additive Manufacturing, Volume 41Author(s): Jingzhou Zhao, Qianzhu Li, Fagang Jin, Nongyue He
A review on the progress and challenges of binder jet 3D printing of sand moulds for advanced casting
09/04/2021 -
Additive Manufacturing, Volume 40Author(s): Tharmalingam Sivarupan, Nagasivamuni Balasubramani, Prateek Saxena, Devarajan Nagarajan, Mohamed El Mansori, Konstantinos Salonitis, Mark Jolly, Matthew S....
Direct 3D printing of multi-level voxel models
09/04/2021 -
Additive Manufacturing, Volume 40Author(s): Sambit Ghadai, Anushrut Jignasu, Adarsh Krishnamurthy
3D printing of continuous fiber-reinforced thermoset composites
09/04/2021 -
Additive Manufacturing, Volume 40Author(s): Xu He, Yuchen Ding, Zepeng Lei, Sam Welch, Wei Zhang, Martin Dunn, Kai Yu
Stereolithography (SLA) 3D printing of an antihypertensive polyprintlet: Case study of an unexpected photopolymer-drug reaction
04/02/2020 -
Additive ManufacturingAuthor(s): Xiaoyan Xu, Pamela Robles-Martinez, Christine M. Madla, Alvaro Goyanes, Fanny Joubert, Abdul W. Basit, Simon GaisfordAbstractThe introduction of three-dimensional...
Embedded 3D Printing of Multi-Internal Surfaces of Hydrogels
04/02/2020 -
Additive ManufacturingAuthor(s): Jingzhou Zhao, Mubashir Hussain, Maonan Wang, Zhiyang Li, Nongyue HeAbstractThe most current 3D printing method involves the combination of additional processes, such...
Experimental study on tensile properties of 3D printed flexible kirigami specimens
04/02/2020 -
Additive ManufacturingAuthor(s): Jun Nakajima, Kazem Fayazbakhsh, Yoshinori TeshimaAbstractFused Filament Fabrication (FFF) is one of the most popular 3D printing processes that can be used to...
Enabling high-performance 3D printing of Al powder by decorating with high laser absorbing Co phase
04/02/2020 -
Additive Manufacturing, Volume 32Author(s): Kang Geng, Yafeng Yang, Shaofu Li, R.D.K. Misra, Qingshan ZhuAbstractPure Al with high laser reflectivity is essentially incompatible with laser powder bed...
Drop-on-demand high-speed 3D printing of flexible milled carbon fiber/silicone composite sensors for wearable biomonitoring devices
04/02/2020 -
Additive Manufacturing, Volume 32Author(s): Elham Davoodi, Haniyeh Fayazfar, Farzad Liravi, Elahe Jabari, Ehsan ToyserkaniAbstractThree-dimensionally (3D) printed flexible piezoresistive composite...
3D printing of bio-based polycarbonate and its potential applications in ecofriendly indoor manufacturing
04/02/2020 -
Additive Manufacturing, Volume 31Author(s): Seong Je Park, Ji Eun Lee, Han Bit Lee, Jeanho Park, Nak-Kyu Lee, Yong Son, Suk-Hee ParkAbstractBiomass-derived polymers have been rapidly developed for...
Ultrasound-assisted 3D printing of continuous fiber-reinforced thermoplastic (FRTP) composites
28/11/2019 -
Additive Manufacturing, Volume 30Author(s): Jing Qiao, Yingrui Li, Longqiu LiAbstractInvestigation of manufacturing continuous ?ber reinforced thermoplastic polymer composites (CFRTPCs) through 3D...
Additive manufacturing aboard a moving vessel at sea using passively stabilized stereolithography (SLA) 3D printing
28/11/2019 -
Additive ManufacturingAuthor(s): Brennan T. Phillips, Josh Allder, Grady Bolan, R. Sean Nagle, Allison Redington, Tess Hellebrekers, John Borden, Nikolai Pawlenko, Stephen LichtAbstractIn this paper...
Fabrication of low dielectric constant composite filaments for use in fused filament fabrication 3D printing
28/11/2019 -
Additive Manufacturing, Volume 30Author(s): Paul Parsons, Zachary Larimore, Faheem Muhammed, Mark MirotznikAbstractIn this paper we describe a method for creating flexible composite filaments with...
Rapid prototyping of cost efficient X-ray collimators
18/09/2019 -
This paper reports on a novel technique for rapid and cost effective manufacture of bespoke X-ray shielding. This technique is particularly well suited for producing prototypes of complex...
3D printing of in-situ curing thermally insulated thermosets
18/09/2019 -
This research reports additive manufacturing of in-situ curing thermosets using direct ink-writing (DIW) process. The investigation reveals the relationships between printing process parameters, such...
Vat photopolymerization 3D printing of ceramics: Effects of fine powder
18/09/2019 -
The objective of this work is to test a novel approach to increase the bulk density of ceramic parts made by vat photopolymerization. It is hypothesized that the bulk density of the resultant ceramic...
3D Printed High Functional Density Packaging Compatible Out-of-Plane Antennas
16/09/2019 -
Additive ManufacturingAuthor(s): Mohd Ifwat Mohd Ghazali, Saranraj Karuppuswami, Amanpreet Kaur, Premjeet ChahalAbstractThis paper demonstrates a simple, low-cost additive manufacturing technique...
A modular path planning solution for Wire + Arc Additive Manufacturing
21/08/2019 -
Robotics and Computer-Integrated Manufacturing, Volume 60Author(s): Florent Michel, Helen Lockett, Jialuo Ding, Filomeno Martina, Gianrocco Marinelli, Stewart WilliamsAbstractWire + Arc Additive...
