Industria 4.0

Industria 4.0

Control of macro-/microstructure and mechanical properties of a wire-arc additive manufactured aluminum alloy
13/05/2020 - Abstract Wire-arc additive manufacturing (WAAM) has received considerable attention in the past years due to advantages in terms of deposition rate, design freedom, and buy-to-fly...
Bayesian optimized deep convolutional network for bearing diagnosis
13/05/2020 - Abstract The successful diagnosis of the faulty signal in rolling element bearings relies on the accurate evaluation of the early fault present within the components of bearings....
Material transitions within multi-material laser deposited intermetallic iron aluminides
13/05/2020 - Additive Manufacturing, Volume 34Author(s): Tobias Hauser, Philipp Peter Breese, Tobias Kamps, Christoph Heinze, Joerg Volpp, Alexander F.H. Kaplan
The effect of hot isostatic pressure on the corrosion performance of Ti-6Al-4?V produced by an electron-beam melting additive manufacturing process
13/05/2020 - Additive Manufacturing, Volume 33Author(s): Avi Leon, Galit Katarivas Levy, Tomer Ron, Amnon Shirizly, Eli Aghion
Big Data Exploration, Visualization and Analytics
12/05/2020 - /description>https://www.sciencedirect.com/science/article/pii/S2214579619302254?dgcid=rss_sd_allhttps://www.sciencedirect.com/science/article/pii/S2214579619302254A Hierarchical Dimension...
COMPARISON OF RANKING MODELS TO EVALUATE DESKTOP 3D PRINTERS IN A GROWING MARKET
12/05/2020 - Additive ManufacturingAuthor(s): Amit J. Lopes, Mireya A. Perez, David Espalin, Ryan B. Wicker
Effects of collagen and casein with phenolic compounds interactions on protein in vitro digestion and antioxidation
21/02/2020 - Bambara bean protein is a promising ingredient for further applications in food and non-food industries. In this study, structural changes in Bambara bean protein isolate (BBPI) produced during high...
Optimization of goat milk vacuum-assisted block freeze concentration using response surface methodology and NaCl addition influence
18/02/2020 - High lipid food matrices are advantageous in protecting probiotic microorganisms during storage and also during digestion. This study aimed to apply enzymatically interesterified milk fat (MF) and...
Encapsulation of Amazonian Blueberry juices: Evaluation of bioactive compounds and stability
18/02/2020 - Release of various genetically modified organisms (GMOs) into market during the past decade contributes to concerns regarding the traceability of food and feed products. In this study, a...
Phase inversion temperature-fabricated cinnamon oil nanoemulsion as a natural preservative for prolonging shelf-life of chilled Asian seabass (Lates calcarifer) fillets
18/02/2020 - In this study, Scomberomorus niphonius surimi was used as the food-ink for 3D printing and microbial transglutaminase (MTGase) as additive, aiming to investigate the effects of MTGase on the...
Measuring hand-pouring motion in casting process using augmented reality marker tracking
11/02/2020 - Abstract Elucidations of workers’ pouring motions and the resultant inflow behavior of molten alloy into the mold are important because the inflow behavior is well known to affect...
Influence of heat treatment temperature on the microstructural, mechanical, and wear behavior of 316L stainless steel fabricated by laser powder bed additive manufacturing
11/02/2020 - Abstract A metal component fabricated by additive manufacturing (AM) is generally required to be heat treated to enhance microstructural and mechanical aspects. This present study...
Radio frequency cooking of pork hams followed with conventional steam cooking
10/02/2020 - Okara has high nutritional value but its high moisture value is a large problem for use as ingredient for food development. The objective of this work was to evaluate the physicochemical...
3D printing of bio-based polycarbonate and its potential applications in ecofriendly indoor manufacturing
04/02/2020 - Additive Manufacturing, Volume 31Author(s): Seong Je Park, Ji Eun Lee, Han Bit Lee, Jeanho Park, Nak-Kyu Lee, Yong Son, Suk-Hee ParkAbstractBiomass-derived polymers have been rapidly developed for...
Correlations of cracking with scan strategy and build geometry in electron beam powder bed additive manufacturing
04/02/2020 - Additive Manufacturing, Volume 32Author(s): Y.S. Lee, M.M. Kirka, J. Ferguson, V.C. PaquitAbstractThe extension of metal additive manufacturing (AM) to non-weldable Ni-based superalloys remains a...
Tailoring polypropylene for extrusion-based additive manufacturing
04/02/2020 - Additive ManufacturingAuthor(s): Minde Jin, Christian Neuber, Hans-Werner SchmidtAbstractThis paper reports on the optimization of polypropylene (PP) feedstock material towards extrusion-based...
The Impact of Integration on Application Success and Customer Satisfaction in Mobile Device Platforms
04/02/2020 - Abstract Digital software platforms allow third parties to develop applications and thus extend their functionality. Platform owners provide platform boundary resources that allow...
Accurate dynamic modeling and control parameters design of an industrial hybrid spray-painting robot
04/02/2020 - Robotics and Computer-Integrated Manufacturing, Volume 63Author(s): Binbin Zhang, Jun Wu, Liping Wang, Zhenyang YuAbstractTo obtain higher performance for hybrid robots subject to nonlinear dynamics...
Development of copper powder paste for direct printing and soft mold casting
04/02/2020 - Additive Manufacturing, Volume 31Author(s): Yao Zhao, Weixiao Gao, Jiaxin Xi, Haoqi Li, Fei RenAbstractRecently, additive manufacturing (AM) of metals has enjoyed significant advancement. While the...
Wire and arc additive manufacturing of a Ni-rich NiTi shape memory alloy: Microstructure and mechanical properties
04/02/2020 - Additive Manufacturing, Volume 32Author(s): Z. Zeng, B.Q Cong, J.P. Oliveira, W.C Ke, N. Schell, B. Peng, Z.W. Qi, F.G Ge, W. Zhang, S.S. AoAbstractWire and Arc Additive Manufacturing (WAAM) was used...
Comparing geometric tolerance capabilities of additive manufacturing systems for polymers
04/02/2020 - Additive ManufacturingAuthor(s): P. Minetola, F. Calignano, M. GalatiAbstractIn all manufacturing processes, there are several factors for which the final product exhibits dimensional and shape...